Supplier needed - RESOLVED NOW
- silverboydreamer
- DDK addict
- Posts: 113
- Joined: Fri Oct 06, 2006 10:05 am
- Location: Solihull
Supplier needed - RESOLVED NOW
Hi, car is a 356 T6 and i need a part that is not listed in the Porsche parts catalogue, it is the reducing angled connector between the body heating tube and the heat valve, photo enclosed.
Can get them from Germany but will cost £100 each which is a bit steep and is likely to give me heart palpitations if I have to shell out £200 plus post.
So if anyone knows anywhere I can them for a reasonable price please let me know, thanks. After a tip-off from a fellow member I found a place to make these in Redditch, it’s call “ everyexhaustpart.com“, a very good reproduction in stainless or mild steel for £ 25.00 each, fitted straight onto car. So thanks for all your comments,
Can get them from Germany but will cost £100 each which is a bit steep and is likely to give me heart palpitations if I have to shell out £200 plus post.
So if anyone knows anywhere I can them for a reasonable price please let me know, thanks. After a tip-off from a fellow member I found a place to make these in Redditch, it’s call “ everyexhaustpart.com“, a very good reproduction in stainless or mild steel for £ 25.00 each, fitted straight onto car. So thanks for all your comments,
Last edited by silverboydreamer on Wed Mar 25, 2020 9:00 am, edited 2 times in total.
Ausfahrt mine Auspuff
-
- Nurse, I think I need some assistance
- Posts: 16918
- Joined: Wed Nov 12, 2003 10:48 pm
- Location: Worcs/W Mids border
Re: Supplier needed
.
If you can't find any for a reasonable price, I'd be tempted to contact an exhaust fabricator - somebody like this:
https://www.ebay.co.uk/itm/Custom-Bend- ... 1154150288
.
If you can't find any for a reasonable price, I'd be tempted to contact an exhaust fabricator - somebody like this:
https://www.ebay.co.uk/itm/Custom-Bend- ... 1154150288
.
Andy
“Adding power makes you faster on the straights;
- subtracting weight makes you faster everywhere”
“Adding power makes you faster on the straights;
- subtracting weight makes you faster everywhere”
- silverboydreamer
- DDK addict
- Posts: 113
- Joined: Fri Oct 06, 2006 10:05 am
- Location: Solihull
Re: Supplier needed
Hi Andy, thanks for that suggestion, by the look of it, it might be TT exhausts as its in Redditch, I have to go over to see him this month so will see what he can do as the pics look as though they are near to what I need.
Regards David
Regards David
Ausfahrt mine Auspuff
Re: Supplier needed
Rich (TT) did a great job on mine
Recommend highly
Steve
Recommend highly
Steve
'72 911T - 212 BHP 2.7, on PMO's
'62 RHD T6 B outlaw
'71 Alfa GT Veloce 2000
1929 Indian 101 'bobber' project.
'40 Indian Sport Scout bobber
VW T5
!920's Racing Cycle
1920's Premier cycle
A few vintage Heuers
Member No 381
'62 RHD T6 B outlaw
'71 Alfa GT Veloce 2000
1929 Indian 101 'bobber' project.
'40 Indian Sport Scout bobber
VW T5
!920's Racing Cycle
1920's Premier cycle
A few vintage Heuers
Member No 381
Re: Supplier needed
Almost positive I bought a set of these from PRS, speak to Paul.
Re: Supplier needed
Here you go!
Tell Paul Eric sent you!
Tell Paul Eric sent you!
- Attachments
-
- Screenshot 2020-02-05 at 22.22.30.png (42.04 KiB) Viewed 1299 times
- silverboydreamer
- DDK addict
- Posts: 113
- Joined: Fri Oct 06, 2006 10:05 am
- Location: Solihull
Re: Supplier needed
Thanks for info, at £74 plus vat it’s all getting into area that’s giving me a lot of stress having to come to terms with paying a lot of money for a bit of tin. Having spent nearly 40 years restoring Porsche’s it never ceases to amaze me how creative suppliers are at charging and 356 prices are heart attack territory for me. Or is it I’m getting too old?
Ausfahrt mine Auspuff
Re: Supplier needed
Yes , 356 prices are high.
It wold be good to see a few pictures of your project.
It wold be good to see a few pictures of your project.
- inaglasshouse
- DDK 1st, 2nd and 3rd for me!
- Posts: 2427
- Joined: Fri Mar 28, 2014 9:35 pm
- Location: Surrey, UK
Re: Supplier needed
But in fairness, very niche market. I doubt any superyachts are being bought with the proceeds.Layercake wrote:Yes , 356 prices are high.
And it is good that our cars continue to be supported by short-run parts suppliers.
-
- Put a fork in me, I'm done!
- Posts: 1852
- Joined: Thu Dec 25, 2008 2:28 pm
- Location: sunny sussex
Re: Supplier needed
I agree might look an easy to reproduce part but....there is more to it than you might think. And if they sell only small quantities this is what drives prices up.
Roy
Roy
RHD 356A coupe super 75 106954
Re: Supplier needed
Totally agree.
They are well made and as my father used to say "it only hurts once"
Buy it and put it behind you,
They are well made and as my father used to say "it only hurts once"
Buy it and put it behind you,
Re: Supplier needed
PRS have a huge amount of second hand parts so might be worth giving them a call to see if they could help? I know Mike from PRS is a regular on here so he might answer for you.
But going back to your point about 356 spares prices - yes they are often eye watering but I think thats because they aren't manufactured in huge quantities due to the very small market. Not sure globally how many 356's are still on the road but I'd guess it's only around 1000? I think the Porsche Club GB has around 200 members with 356's albeit they aren't necessarily all on the road.
But going back to your point about 356 spares prices - yes they are often eye watering but I think thats because they aren't manufactured in huge quantities due to the very small market. Not sure globally how many 356's are still on the road but I'd guess it's only around 1000? I think the Porsche Club GB has around 200 members with 356's albeit they aren't necessarily all on the road.
1964 Porsche 356c (RHD)
1957 Vespa GS 150 VS3
1960 Vespa GS 150 VS5
1960 Lambretta Li125
1963 Lambretta Li150 series 3
1962 Lambretta TV175
1966 Lambretta SX200
1957 Vespa GS 150 VS3
1960 Vespa GS 150 VS5
1960 Lambretta Li125
1963 Lambretta Li150 series 3
1962 Lambretta TV175
1966 Lambretta SX200
-
- DDK rules my life!
- Posts: 1229
- Joined: Wed Apr 06, 2005 12:37 am
- Location: Billericay, Essex
- Contact:
Re: Supplier needed
The reason that we replicated this part is because we coud never find one - when we needed it for a customer, so I know that we do not have any used ones
The Market is extremely small for this part (it was only used on Late Cars) and I am sure that `currently` we are the only people making them (the ones from Germany are our production.
Of course, we had to produce the tooling for it and it is a complcated little dude to produce and we are lucky to have a guy that will turn out these small quantities for us
Will we make another run of them ? - who knows?
Happy Hunting - Keep The Faith
The Market is extremely small for this part (it was only used on Late Cars) and I am sure that `currently` we are the only people making them (the ones from Germany are our production.
Of course, we had to produce the tooling for it and it is a complcated little dude to produce and we are lucky to have a guy that will turn out these small quantities for us
Will we make another run of them ? - who knows?
Happy Hunting - Keep The Faith
Mike at P.R.S.
www.prs356.com
www.prs356.com
-
- DDK Newbie
- Posts: 8
- Joined: Mon Oct 16, 2017 9:28 pm
Re: Supplier needed
Stop moaning about shelling out a few quid.. with a wallet so stuffed it makes you walk with a limp.
Get buying .. the money you save will buy you your beer for a decade at Wetherspoon's.
We know where you live ..
Get buying .. the money you save will buy you your beer for a decade at Wetherspoon's.
We know where you live ..