Hello guys. Need to get my frames re-anodised so got to remove them from front and rear window seals.
Any special way to do it without damaging ?
Going to run them to Nick soon. They are still in the seal and on the windows.
What are they like putting back in the front and rear window seals and on the windows.
What are the steps to take first?
Thanks Lee
Sent from my iPhone using Tapatalk
Window frame removal
Moderators: hot66, impmad2000, Barry, Viv_Surby, Derek, Mike Usiskin
-
- DDK rules my life!
- Posts: 1176
- Joined: Thu Feb 10, 2011 1:22 pm
- Location: lowestoft,suffolk
Window frame removal
1969 911t, eighth off the production line - B Series, Collecting Parts Again for Resto.
1984 Devon T25 VW Campervan, Back on the Road
1969 Italian Lambretta GP200. Tuned, (restored)
1967 Italian Lambretta SX150, 3 owner, 5 Speed, (Restored)
1984 Devon T25 VW Campervan, Back on the Road
1969 Italian Lambretta GP200. Tuned, (restored)
1967 Italian Lambretta SX150, 3 owner, 5 Speed, (Restored)
-
- Nurse, I think I need some assistance
- Posts: 10320
- Joined: Wed Mar 31, 2004 1:27 pm
- Location: Cheshire
- Contact:
Re: Window frame removal
Do you mean the windscreen/rear window trim?
Most people just buy new if they are bad. Keeping them even vaguely the right shape whilst being polished and anodised will be very hard and I’d imagine the cost of doing so would exceed the new cost.
Are your windows out? You can’t get the trim out and back in again with them in the car.
Most people just buy new if they are bad. Keeping them even vaguely the right shape whilst being polished and anodised will be very hard and I’d imagine the cost of doing so would exceed the new cost.
Are your windows out? You can’t get the trim out and back in again with them in the car.
-
- DDK rules my life!
- Posts: 1176
- Joined: Thu Feb 10, 2011 1:22 pm
- Location: lowestoft,suffolk
Re: Window frame removal
Really oh?
I could probably live with my front ant rear trim but my door window trim and rear quarter needs work I think.
Yes all my windows are out. I want to try and get them ready to go back in now.
Thanks Lee
Sent from my iPhone using Tapatalk
I could probably live with my front ant rear trim but my door window trim and rear quarter needs work I think.
Yes all my windows are out. I want to try and get them ready to go back in now.
Thanks Lee
Sent from my iPhone using Tapatalk
1969 911t, eighth off the production line - B Series, Collecting Parts Again for Resto.
1984 Devon T25 VW Campervan, Back on the Road
1969 Italian Lambretta GP200. Tuned, (restored)
1967 Italian Lambretta SX150, 3 owner, 5 Speed, (Restored)
1984 Devon T25 VW Campervan, Back on the Road
1969 Italian Lambretta GP200. Tuned, (restored)
1967 Italian Lambretta SX150, 3 owner, 5 Speed, (Restored)
-
- Nurse, I think I need some assistance
- Posts: 10320
- Joined: Wed Mar 31, 2004 1:27 pm
- Location: Cheshire
- Contact:
Re: Window frame removal
Door and quarter frames you can take apart and extract the glass to allow polishing and anodising. I couldn’t get my 1/4 windows out of the frames (all the fixings were seized) so had a change of plan and stripped them by hand (oven cleaner gets the original anodising off) then sanded and polished with increasing grades. Finally a buff and done.
Been like that since the rebuild with a few thousand miles in all weathers with no special care and still look just fine, no corrosive or tarnish.
Been like that since the rebuild with a few thousand miles in all weathers with no special care and still look just fine, no corrosive or tarnish.
Re: Window frame removal
I replaced my front window trim. Much easier and probably cheaper than getting them replaced.
My Front window frames were re-anodised by Nick: http://www.early911.co.uk/html/alloy_trim.html. However, the screw thread inserts in the frame are steel which the anodising process dissolved. The inserts were not removed and replaced in the process, so they get masked and the result gives a partial reanodising. The bits that can be seen look good though.
Paul
My Front window frames were re-anodised by Nick: http://www.early911.co.uk/html/alloy_trim.html. However, the screw thread inserts in the frame are steel which the anodising process dissolved. The inserts were not removed and replaced in the process, so they get masked and the result gives a partial reanodising. The bits that can be seen look good though.
Paul
1970 2.2 911 T / Ex RS Clone, now more original looking, with 1979 3.2 SS engine
1988 3.2 Carrera Commemorative edition (sold)
1988 3.2 Carrera Commemorative edition (sold)