Front 'Euro' lenses for a '67

An archive of any Porsche 911 technical threads

Moderators: hot66, impmad2000, Barry, Viv_Surby, Derek, Mike Usiskin

Post Reply
User avatar
hot66
Moderator
Posts: 19219
Joined: Tue Nov 11, 2003 4:17 pm
Location: North Yorkshire

Front 'Euro' lenses for a '67

Post by hot66 »

My '67 has US spec 'all orange' front lenses. I am still debating wether to leave her as she left the factory ( although the rear lenses have already been changes to euro spec) or fit some euro front lenses.

I gather the SWB lenses/light units are one piece. Is it a straight forward job to install eurolenses & can it be done without damaging the originals that are all ready on the car?
James

1973 911 2.4S
1993 964 C2
2010 987 Spyder

1963 Honda C100 Supercub

Its not how fast you go, but how you go fast ;)
lewis
DDK above all
Posts: 197
Joined: Tue Feb 24, 2004 4:06 pm
Location: luton
Contact:

Post by lewis »

Its not dificult to change the lenses you have to break off the tabs that hold on the original then bond on the new ones with clear silicone. I changed my rear lights because you cant show a red indicator and I did not like the idea of amber lenses in the reversing lights. The fronts I have left in situe and used H4'swith sidelights the amber lights are now indicator only, problem solved. :)

lewis
68 912
Lightweight_911
Nurse, I think I need some assistance
Posts: 17995
Joined: Wed Nov 12, 2003 10:48 pm
Location: Worcs/W Mids border

Post by Lightweight_911 »

James - you can't remove the existing lenses without damaging them. They are held on by 2 brass hollow rivets (through which the mounting screws pass) & a number of 'melted' plastic tabs on the reverse - you need to drill out the rivets & break off the plastic tabs to remove the lens.

In true 'Haynes manual fashion' installation of the new lenses is the reverse of the removal of the old ones - I use a large soldering iron to melt the tabs on the rear (after you install the brass rivets). As Martin said above, any small gap left around the perimeter of the lens can be sealed using a thin bead of clear silicone.

It's purely personal but I much prefer the look of Euro F&R lamps on early 911/912's.
Andy

“Adding power makes you faster on the straights;
- subtracting weight makes you faster everywhere”
User avatar
hot66
Moderator
Posts: 19219
Joined: Tue Nov 11, 2003 4:17 pm
Location: North Yorkshire

Post by hot66 »

thought that was the case. I too prefer the euro lenses. Think I'll run the car for a bit then decide :)
James

1973 911 2.4S
1993 964 C2
2010 987 Spyder

1963 Honda C100 Supercub

Its not how fast you go, but how you go fast ;)
Gone in 60 seconds
DDK slapper chatter
Posts: 302
Joined: Sun Apr 18, 2004 2:19 am
Location: Oxford
Contact:

Post by Gone in 60 seconds »

James,
Just going to agree with Andy and your comments, I ve changed all the lamps on my car from Euro spec since importing, the main reason is just aesthetic, it passed the MOT with orange lenses, I just think they look good, and to be honest in the sea of orange that is my car the break is a welcome change!
73 911 RS(T) #0968
chris68
DDK forever
Posts: 523
Joined: Thu Apr 28, 2005 12:54 pm
Location: Burton On Trent

Euro Lenses

Post by chris68 »

Hi,

Can anyone suggest the best place to get replacement pre '68 lenses.

Cheers,
Chris
'68 swb 911L (rhd)
'62 Lotus 22 (sold)
100cc Historic Karts
Lightweight_911
Nurse, I think I need some assistance
Posts: 17995
Joined: Wed Nov 12, 2003 10:48 pm
Location: Worcs/W Mids border

Post by Lightweight_911 »

Quite a few options in the UK including Roger Bray:

http://www.rogerbrayrestoration.com/

& Russell Ward:

http://www.partssource.autopage.co.uk/

Or Mittelmotor, Lenz Trend, Maria Habeck, etc in Germany.
Andy

“Adding power makes you faster on the straights;
- subtracting weight makes you faster everywhere”
Post Reply