1965 Hillman Imp soon with flat six from a Honda
Moderator: Bootsy
-
- Nurse, I think I need some assistance
- Posts: 18951
- Joined: Mon Mar 10, 2008 6:26 pm
- Location: West Midlands
Re: 1965 Hillman Imp soon with flat six from a Honda
Wonderful as ever!!
The trigger in the lathe pic bought some memories back!
What a great result and what a start-up!
Sounds very nice and surprisingly quiet to me.
What rad will you use?
The trigger in the lathe pic bought some memories back!
What a great result and what a start-up!
Sounds very nice and surprisingly quiet to me.
What rad will you use?
73T 911 Coupe, road/hillclimber 3.2L
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Re: 1965 Hillman Imp soon with flat six from a Honda
Thanks fellas.
Yes- a bit quieter than I was expecting and much smoother considering its on a default tune that is made to suit the mean average of engines out there. I dont think I'm going to put too much effort into making the silencer really effective as I want to hear this thing!
I need to start drawing up some designs for the exhaust box. It'll be based on a typical older 911 design but like the rs 2.7 with centre exit pipes..
they seem quite basic inside... I plan on making mine in stainless with a removable lid so I can easily open it and alter the design within. I'm keen to hear any opinions or suggestions on what makes for a good box.
Yes- a bit quieter than I was expecting and much smoother considering its on a default tune that is made to suit the mean average of engines out there. I dont think I'm going to put too much effort into making the silencer really effective as I want to hear this thing!
I need to start drawing up some designs for the exhaust box. It'll be based on a typical older 911 design but like the rs 2.7 with centre exit pipes..
they seem quite basic inside... I plan on making mine in stainless with a removable lid so I can easily open it and alter the design within. I'm keen to hear any opinions or suggestions on what makes for a good box.
-
- Nurse, I think I need some assistance
- Posts: 18951
- Joined: Mon Mar 10, 2008 6:26 pm
- Location: West Midlands
Re: 1965 Hillman Imp soon with flat six from a Honda
My 73T 911 has a 3.2 engine in it and has used a sports exhaust for the last 28 years (I've had the car since 1988).
It has 3 outlet pipes and two inlet.
It is a factory sports rally silencer.
The two additional pipes are capped over for road use and the stock side output does the quiet work.
No droning etc, nice and friendly to people around me (Police getting heavy on noise cars in the UK now).
Every now and then when I feel a bit 'boy-racerish' I will remove the two caps so exhaust flows from all 3 outlets.
The tick over rises to 950 rpm from 800 and throttle response is much sharper, and the sound is near straight through, fabulous and addictive...
Wife does not like it so it must be good.
Find a web site for 'Turbo Thomas' here in the UK, he makes custom silencers for 911's, might give you a few ideas.
The diagram you show is a popular mod for a stock 911 silencer. I know someone who had converted his Dansk stainless silencer this way and it works very well with no droning at 70 mph etc.
This is the engine from my 911:
It has 3 outlet pipes and two inlet.
It is a factory sports rally silencer.
The two additional pipes are capped over for road use and the stock side output does the quiet work.
No droning etc, nice and friendly to people around me (Police getting heavy on noise cars in the UK now).
Every now and then when I feel a bit 'boy-racerish' I will remove the two caps so exhaust flows from all 3 outlets.
The tick over rises to 950 rpm from 800 and throttle response is much sharper, and the sound is near straight through, fabulous and addictive...
Wife does not like it so it must be good.
Find a web site for 'Turbo Thomas' here in the UK, he makes custom silencers for 911's, might give you a few ideas.
The diagram you show is a popular mod for a stock 911 silencer. I know someone who had converted his Dansk stainless silencer this way and it works very well with no droning at 70 mph etc.
This is the engine from my 911:
73T 911 Coupe, road/hillclimber 3.2L
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Re: 1965 Hillman Imp soon with flat six from a Honda
Great! Thanks for the info. I'll look up turbo Thomas.
I'm quite looking forward to this part of the build when it comes. I'm sick of the steel silencer I made for the imp that currently keeps getting rust holes in the bottom plus it's too low for steep driveway exits in town.
I'm quite looking forward to this part of the build when it comes. I'm sick of the steel silencer I made for the imp that currently keeps getting rust holes in the bottom plus it's too low for steep driveway exits in town.
-
- Nurse, I think I need some assistance
- Posts: 18951
- Joined: Mon Mar 10, 2008 6:26 pm
- Location: West Midlands
Re: 1965 Hillman Imp soon with flat six from a Honda
No!! Lol
He is a long established small exhaust system guy, originally focused on VW parts.
Mind you, it was about 5 years ago since I last saw his site…
He is a long established small exhaust system guy, originally focused on VW parts.
Mind you, it was about 5 years ago since I last saw his site…
73T 911 Coupe, road/hillclimber 3.2L
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
-
- I need to get out more!
- Posts: 3277
- Joined: Mon Apr 26, 2004 7:51 am
- Location: Selby
Re: 1965 Hillman Imp soon with flat six from a Honda
http://www.ttexhausts.com/
Interestingly the RSrep on his opening page was mine and TT exhaust was a beaut!
Interestingly the RSrep on his opening page was mine and TT exhaust was a beaut!
Merc B Class diesel
Porsche-less
Porsche-less
Re: 1965 Hillman Imp soon with flat six from a Honda
Hope your well Mick.Mick Cliff wrote: ↑Thu Jan 25, 2024 5:09 am http://www.ttexhausts.com/
Interestingly the RSrep on his opening page was mine and TT exhaust was a beaut!
No regrets selling the rep?
.
Regards,
Dougie
Worry is the interest on inevitability !
Dougie
Worry is the interest on inevitability !
-
- I need to get out more!
- Posts: 3277
- Joined: Mon Apr 26, 2004 7:51 am
- Location: Selby
Re: 1965 Hillman Imp soon with flat six from a Honda
Tolerably well thanks Dougie. Hope you and Kate are well too.
The time was right for me to sell and slow down! No regrets but do miss that car and the 10 Years of raucous fun!
Merc B Class diesel
Porsche-less
Porsche-less
Re: 1965 Hillman Imp soon with flat six from a Honda
From the TT website - this is the exit style I'll be building...
Re: 1965 Hillman Imp soon with flat six from a Honda
Now I had an engine that starts and runs for half a minute I wanted more. I needed a makeshift cooling setup.
I had a spare Nissan March radiator and fan kicking about so that was called into action. I whipped up this beautiful bit of carpentry artwork..
Using a collection of spare hoses I connected the dots between the engine, the electric water pump and the radiator...
I started filling the system with coolant mixed at 35%. Remember this bit. It comes back to haunt me later.
The whole system wouldn't fill up due an airlock in the coolant pipe from the opposite head. There was no way this was going to shift. The standard goldwing cooling system has both top pipes meeting in the middle at a thermostat block so they just bleed the air straight out naturally.
I needed a nipple.
I looked in my collection of various sized nipples and other brake fittings...
Found this small nipple which was perfectly formed and a lovely size...
I needed a boss to inset the nipple into. I machined one up and tig welded it carefully onto the top of the coolant pipe, in a discrete place tucked away behind the alternator so the nipple isn't immediately on display unless you look for it.
Now with the nipple cracked open the large airlock was able leave via some clear vinyl tube. This allowed almost 1.5 litres more coolant in. With the water pump in override mode and twisted sideways I was able to bleed the pump out and the coolant was circulating fine.
Next step before running the engine for an extended period was to sort out the O2 sensor positioning. Luckily a nice stainless boss from ali land had turned up so that was welded in place ...
I was very happy that I could run the sensor cable around behind the oil filter, completely out of harms way and about as out of view as I could hope for. There's no hiding the ugly sensor sticking out of the exhaust but that's just life.
The exhaust also required a token amount of silencing so I popped the old motorbike silencers outside on the truck deck and painted them with black high temp paint, mainly so I wasn't looking at ugly rusty things..
I also had to do a little bit of extra wiring. The water pump and its controller, the O2 gauge and not to forget the remote unit for the mandalorian spaceship interior lights..
I also wanted to slot my throttle cable adjuster base so I could easily remove the whole cable outer and inner without fuss...
In the mill with a tiny slot drill...
I made a hand throttle using a spare mountain bike brake lever and a bit of suitable alloy tube. But I needed a tiny solderless nipple for the cable end. My tray of bike cable adjusters and such what had nothing small enough so I machined one out of brass and used a 3mm grub screw...
Now I had some basic throttle control without reaching over the engine.
Time to start it up which happened without any fuss. The coolant system worked fine and the engine rose to temp quickly and smoothly. The fan kicks in above my for now setting of 98 degrees. I intended to tune the idle first, once the engine was hot and not using any of the warm up tables etc. But the idle control valve was still passing a touch too much air even when 'closed'. I wound the idle bleed screw in to its stop on the throttle body but still it was idling at 1200 thereabouts. If I blocked the iacv inlet with my finger the revs would drop to circa 700-800. I could also hear a very tiny vac leak from the spaceship window (plenum lid)
Bloody Mandalorians with their terrible glazing skills.
Tightened the lid bolts down and its not bad. Main issue really is the idle valve. I might just make my own like I did with the Mazda V6. Rip the guts out from a stock Mazda item and machine a suitable body to take the solenoid and valve head.
Another issue far more critical that really had me feeling quite low was this...
Coming from here...
Coolant gallery at base of the head gaskets on each side. It's not dripping but weeping and only once up to temp. I was gutted. I had to travel over to Nelson city that afternoon in my Imp so while there I popped into the engine reconditioners I know there and explained the problem and showed them the photos. Instantly they said I shouldn't have done my first fill with coolant. Apparently it creeps very effectively through any tiny gap before the head gasket has sealed and its slippery/slightly slimy consistency stops the paint on the gasket sticking to the surfaces. All is not lost though. I was instructed to drain the system of coolant, flush everything through thoroughly with clean water and let it dry. I did that last night. I then ran it a couple of times this morning with nothing in it for no more than 30 seconds, allowing it to cool between. Hopefully this will have dried it out and help it seal. Then I was told to just run it with water for a while and see how it goes. It might be ok. If not then they have a kiwi made product called sealwel that many kiwi/aussie reconditioners use with troublesome gaskets. He reckoned its not failed them.
Worst case scenario is a pair of new head gaskets.
and no coolant when setting them !
I might just order the gaskets just in case so I'm not ever in a position where I have to wait later on down the road if the above doesn't work.
So yeah. I hope its ok and I've plenty of other things to do anyway. Like sort out the alternator that seems to be defective. This one. I need to either fix it or find an exact replacement because the spaceship has been built up to it and there's no room for anything bigger/longer..
I have also chopped the throttle body spring back a half coil for more tension on the throttle shut. It wasn't closing completely by itself against the strength of the engine want of air.
I had a spare Nissan March radiator and fan kicking about so that was called into action. I whipped up this beautiful bit of carpentry artwork..
Using a collection of spare hoses I connected the dots between the engine, the electric water pump and the radiator...
I started filling the system with coolant mixed at 35%. Remember this bit. It comes back to haunt me later.
The whole system wouldn't fill up due an airlock in the coolant pipe from the opposite head. There was no way this was going to shift. The standard goldwing cooling system has both top pipes meeting in the middle at a thermostat block so they just bleed the air straight out naturally.
I needed a nipple.
I looked in my collection of various sized nipples and other brake fittings...
Found this small nipple which was perfectly formed and a lovely size...
I needed a boss to inset the nipple into. I machined one up and tig welded it carefully onto the top of the coolant pipe, in a discrete place tucked away behind the alternator so the nipple isn't immediately on display unless you look for it.
Now with the nipple cracked open the large airlock was able leave via some clear vinyl tube. This allowed almost 1.5 litres more coolant in. With the water pump in override mode and twisted sideways I was able to bleed the pump out and the coolant was circulating fine.
Next step before running the engine for an extended period was to sort out the O2 sensor positioning. Luckily a nice stainless boss from ali land had turned up so that was welded in place ...
I was very happy that I could run the sensor cable around behind the oil filter, completely out of harms way and about as out of view as I could hope for. There's no hiding the ugly sensor sticking out of the exhaust but that's just life.
The exhaust also required a token amount of silencing so I popped the old motorbike silencers outside on the truck deck and painted them with black high temp paint, mainly so I wasn't looking at ugly rusty things..
I also had to do a little bit of extra wiring. The water pump and its controller, the O2 gauge and not to forget the remote unit for the mandalorian spaceship interior lights..
I also wanted to slot my throttle cable adjuster base so I could easily remove the whole cable outer and inner without fuss...
In the mill with a tiny slot drill...
I made a hand throttle using a spare mountain bike brake lever and a bit of suitable alloy tube. But I needed a tiny solderless nipple for the cable end. My tray of bike cable adjusters and such what had nothing small enough so I machined one out of brass and used a 3mm grub screw...
Now I had some basic throttle control without reaching over the engine.
Time to start it up which happened without any fuss. The coolant system worked fine and the engine rose to temp quickly and smoothly. The fan kicks in above my for now setting of 98 degrees. I intended to tune the idle first, once the engine was hot and not using any of the warm up tables etc. But the idle control valve was still passing a touch too much air even when 'closed'. I wound the idle bleed screw in to its stop on the throttle body but still it was idling at 1200 thereabouts. If I blocked the iacv inlet with my finger the revs would drop to circa 700-800. I could also hear a very tiny vac leak from the spaceship window (plenum lid)
Bloody Mandalorians with their terrible glazing skills.
Tightened the lid bolts down and its not bad. Main issue really is the idle valve. I might just make my own like I did with the Mazda V6. Rip the guts out from a stock Mazda item and machine a suitable body to take the solenoid and valve head.
Another issue far more critical that really had me feeling quite low was this...
Coming from here...
Coolant gallery at base of the head gaskets on each side. It's not dripping but weeping and only once up to temp. I was gutted. I had to travel over to Nelson city that afternoon in my Imp so while there I popped into the engine reconditioners I know there and explained the problem and showed them the photos. Instantly they said I shouldn't have done my first fill with coolant. Apparently it creeps very effectively through any tiny gap before the head gasket has sealed and its slippery/slightly slimy consistency stops the paint on the gasket sticking to the surfaces. All is not lost though. I was instructed to drain the system of coolant, flush everything through thoroughly with clean water and let it dry. I did that last night. I then ran it a couple of times this morning with nothing in it for no more than 30 seconds, allowing it to cool between. Hopefully this will have dried it out and help it seal. Then I was told to just run it with water for a while and see how it goes. It might be ok. If not then they have a kiwi made product called sealwel that many kiwi/aussie reconditioners use with troublesome gaskets. He reckoned its not failed them.
Worst case scenario is a pair of new head gaskets.
and no coolant when setting them !
I might just order the gaskets just in case so I'm not ever in a position where I have to wait later on down the road if the above doesn't work.
So yeah. I hope its ok and I've plenty of other things to do anyway. Like sort out the alternator that seems to be defective. This one. I need to either fix it or find an exact replacement because the spaceship has been built up to it and there's no room for anything bigger/longer..
I have also chopped the throttle body spring back a half coil for more tension on the throttle shut. It wasn't closing completely by itself against the strength of the engine want of air.
-
- Put a fork in me, I'm done!
- Posts: 1647
- Joined: Fri Mar 01, 2013 11:45 am
- Location: Kernow - good old Cornwall
Re: 1965 Hillman Imp soon with flat six from a Honda
Brilliant work - not sure if that alternator is not the same one fitted to Suzuki SJ413 and early Suzuki Swifts.
It is also fitted to early Honda Ballade’s - shows the Bosch alternative a 31100-P2C-K01 back referenced to the Mitsubishi part number??
It is also fitted to early Honda Ballade’s - shows the Bosch alternative a 31100-P2C-K01 back referenced to the Mitsubishi part number??
-
- Nurse, I think I need some assistance
- Posts: 8771
- Joined: Sat Apr 23, 2005 9:08 pm
- Location: Nottingham, UK
Re: 1965 Hillman Imp soon with flat six from a Honda
Awesome work again - thanks for sharing
The simple things you see are all complicated
I look pretty young but I'm just backdated yeah
I look pretty young but I'm just backdated yeah
Re: 1965 Hillman Imp soon with flat six from a Honda
I drained all the coolant out, took the radiator and pipework off and flushed the whole lot through until only clean water flowed. Let it sit in the sun while I did other jobs and gave the engine a couple of short 30 second runs to help dry it right out.
I left it at that and decided to sort out the idle control valve that wont shut completely. I started by removing it and putting it somewhere it'll probably just collect dust for a few months and then maybe get sold/thrown in a bin. I then took Hannah on another exciting date to the local wreckers where we looked under many bonnets to find a suitable replacement.
'Automotive foraging' I like to call it. Here I am in the wilds of the wreckers...
I took home a couple of throttle bodies with valves attached. One from a Mazda 3 and the other from a Mazda 626. They had almost identical iacvs but one had an adjustment. I cut a section of alloy out of a big block..
Milled it flat and square..
Throttle bodies..
tested them with some pipe and the earlier 626 item has a similar fail safe to my now removed Bosch item, whereby it still lets air through when 'off'.
So that just wont do and I have decided the keeper...
Mazda 3 unit wins this competition and gets to stay in the workshop while the 626 item went in the bin.
I did some more machining of the block so turning it into a ported hub the iacv bolts to, with an in and out pipe pressed in place. I made a bracket to suit the starter motor through bolts to which the aicv block bolts onto. In pictures..
Bolts onto starter like so...
Ended up being not only more compact and better mounted than the old Bosch unit but with better pipe routing too.
I ran the valve through some tests on tuner studio and it works really well, shuts properly and is also much much quieter , partly due to it running at a much higher frequency than the Bosch unit.
The next thing I thought I'd check was the headbolts out of curiosity to see if they were still torqued up fine. I first laid out some neat material that was absorbent, but waterproof. My sister, a surgery nurse at Wellington hospital, gave it to me and said its handy stuff to have about. Certainly is!...
Bolts were all fine and I saw no point in giving them anything extra beyond what Mr Honda specifies, so possibly risking deformation of the heads etc.
Next thing was to sort out the electric water pump placement. Where I had mounted it turned out to make it a pig to bleed of air due to the outlet pointing downhill and I knew it could be better. See here...
I removed the mounting bracket I'd made for it...
Unplugged the ecu etc etc and slid the whole engine/transmission onto the the 'engine stand 2000'. This process is super easy as it can be adjusted to the same height as the big table or workshop bench and the engine slides really nicely on the ribbed sump.
Then I slung it into the spare imp and tried out the water pump for size in the new location I had in mind...
Cooling pipework serving the Datsun engine exit the bodyshell roughly about here...
Much better position. Not only will the pump almost self bleed, being at about the lowest point in the cooling system, but I will also clear up the area of uglyness where it used to be. It also gives me full easy access to the transmission filler/dipstick.
I removed the engine, put it back on the table and set to work marking out for a mounting bracket...
Then fabricated this bracket..
Which mounts the pump here...
New improved temporary cooling setup which filled up sweet and bleed of air easily..
Quality touches..
With the cooling system now filled with just water I ran the engine up to temp. The new iacv was working well and I was more confident in running the engine for as long as my lunchbox fuel can would allow. I kept checking for any leaks and found nothing. The cooling system was working well, the fan kicking on and off, the temp staying around the 95- 97 degrees range I had set on the water pump controller (which also controls the fan relay) and I was finally able to set the idle properly with the idle bleed screw on the throttle body - something I was not able to do with the Bosch iacv which was letting in too much air.
Still no leaks. I ran it several times, let it cool down, checked it the following morning and the level was spot on. Touch wood but I think the extra heat and lack of slippery coolant has allowed the head gaskets to 'set'. Either that or maybe there wasn't a leak at all and it was just residue coolant from spillage when I had removed the top pipes to pressure test them.
Anyway.. I was a farking happy bloke! (Hannah was super happy for me too)
Now with the coolant system working and it idling nicely etc I had the confidence to finally give the engine a decent rev up and see what it sounds like at 6000 rpm. Hannah took a vid...
https://www.youtube.com/watch?v=6HtxaBm46sU
I just love that sound. The overrun rasp that flat sixes make. It revs up so quick and clean (and there's no acceleration enrichment setup on the tune yet until I sort the main fuel table later on so it can bog if you snap the throttle open too quickly)
Another vid I took showing the hand throttle...
https://www.youtube.com/watch?v=YNh-SbdphIE
So far the little Mandalorians have managed to keep all their limbs in place. In fact the plenum chamber stays quite cool with the constant stream of cool air flowing into it.
Their spaceship has aircon?
Anyway. I was happy. The only issue was that the whole time I have been running it without any alternator so meaning the ecu is having to use the voltage compensation tables and its not really an ideal situation having everything running at 2-3 volts less than it should.
I took my alternator apart again and ran through as many checks I could, following a very handy NZ auto electrical school tutor video about alternator testing online. I suspect the rectifier is kaput and I couldn't locate a cheap replacement.
I managed to locate a second hand alternator, pretty much the same unit and have bought it - now just waiting on the seller to sort their sh1t out.
In the meantime I got another similar alternator, this time a nippon denso unit from a Honda prelude that actually has a bit more clearance out back, but with an ugly grey painted steel cover. I ran some pigtail connections and bolted it up, started the engine and now have charging! Yay.
With things running at full voltage I tweaked the engines idle tune and cold start settings and am much happier with where I'm at there.
In case the other alternator turns out to not arrive/be a dud etc I decided to give this working unit I do have a bit of a polish and paint. In pics, finishing it off with wrinkle finish paint on the tin end cover.
Much better looking. I bolted it back in place and did one final run up to temp with a bit more tuning of the fuel table idle zone. I now have the engine able to idle at 650 and I could almost get a 50cent coin to balance on the plenum lid. The engine is still only sitting on the table, not bolted in place so I cant really expect it to be perfectly smooth. I think it idles a bit nicer at around 750- 800, a zone where its also running leaner at close to 14.7. Lots of time in the future to play with settings.
Confident its all a good starter and idler, plus realising I'm stalling on the next stage, I have now started to take the pump controller, cooling system and temporary wiring apart. The next time it will be started will hopefully be in the Imp. Next job is to reassemble the transmission, bolt the lot into the spare shell and sort out the gear shift linkage.
I left it at that and decided to sort out the idle control valve that wont shut completely. I started by removing it and putting it somewhere it'll probably just collect dust for a few months and then maybe get sold/thrown in a bin. I then took Hannah on another exciting date to the local wreckers where we looked under many bonnets to find a suitable replacement.
'Automotive foraging' I like to call it. Here I am in the wilds of the wreckers...
I took home a couple of throttle bodies with valves attached. One from a Mazda 3 and the other from a Mazda 626. They had almost identical iacvs but one had an adjustment. I cut a section of alloy out of a big block..
Milled it flat and square..
Throttle bodies..
tested them with some pipe and the earlier 626 item has a similar fail safe to my now removed Bosch item, whereby it still lets air through when 'off'.
So that just wont do and I have decided the keeper...
Mazda 3 unit wins this competition and gets to stay in the workshop while the 626 item went in the bin.
I did some more machining of the block so turning it into a ported hub the iacv bolts to, with an in and out pipe pressed in place. I made a bracket to suit the starter motor through bolts to which the aicv block bolts onto. In pictures..
Bolts onto starter like so...
Ended up being not only more compact and better mounted than the old Bosch unit but with better pipe routing too.
I ran the valve through some tests on tuner studio and it works really well, shuts properly and is also much much quieter , partly due to it running at a much higher frequency than the Bosch unit.
The next thing I thought I'd check was the headbolts out of curiosity to see if they were still torqued up fine. I first laid out some neat material that was absorbent, but waterproof. My sister, a surgery nurse at Wellington hospital, gave it to me and said its handy stuff to have about. Certainly is!...
Bolts were all fine and I saw no point in giving them anything extra beyond what Mr Honda specifies, so possibly risking deformation of the heads etc.
Next thing was to sort out the electric water pump placement. Where I had mounted it turned out to make it a pig to bleed of air due to the outlet pointing downhill and I knew it could be better. See here...
I removed the mounting bracket I'd made for it...
Unplugged the ecu etc etc and slid the whole engine/transmission onto the the 'engine stand 2000'. This process is super easy as it can be adjusted to the same height as the big table or workshop bench and the engine slides really nicely on the ribbed sump.
Then I slung it into the spare imp and tried out the water pump for size in the new location I had in mind...
Cooling pipework serving the Datsun engine exit the bodyshell roughly about here...
Much better position. Not only will the pump almost self bleed, being at about the lowest point in the cooling system, but I will also clear up the area of uglyness where it used to be. It also gives me full easy access to the transmission filler/dipstick.
I removed the engine, put it back on the table and set to work marking out for a mounting bracket...
Then fabricated this bracket..
Which mounts the pump here...
New improved temporary cooling setup which filled up sweet and bleed of air easily..
Quality touches..
With the cooling system now filled with just water I ran the engine up to temp. The new iacv was working well and I was more confident in running the engine for as long as my lunchbox fuel can would allow. I kept checking for any leaks and found nothing. The cooling system was working well, the fan kicking on and off, the temp staying around the 95- 97 degrees range I had set on the water pump controller (which also controls the fan relay) and I was finally able to set the idle properly with the idle bleed screw on the throttle body - something I was not able to do with the Bosch iacv which was letting in too much air.
Still no leaks. I ran it several times, let it cool down, checked it the following morning and the level was spot on. Touch wood but I think the extra heat and lack of slippery coolant has allowed the head gaskets to 'set'. Either that or maybe there wasn't a leak at all and it was just residue coolant from spillage when I had removed the top pipes to pressure test them.
Anyway.. I was a farking happy bloke! (Hannah was super happy for me too)
Now with the coolant system working and it idling nicely etc I had the confidence to finally give the engine a decent rev up and see what it sounds like at 6000 rpm. Hannah took a vid...
https://www.youtube.com/watch?v=6HtxaBm46sU
I just love that sound. The overrun rasp that flat sixes make. It revs up so quick and clean (and there's no acceleration enrichment setup on the tune yet until I sort the main fuel table later on so it can bog if you snap the throttle open too quickly)
Another vid I took showing the hand throttle...
https://www.youtube.com/watch?v=YNh-SbdphIE
So far the little Mandalorians have managed to keep all their limbs in place. In fact the plenum chamber stays quite cool with the constant stream of cool air flowing into it.
Their spaceship has aircon?
Anyway. I was happy. The only issue was that the whole time I have been running it without any alternator so meaning the ecu is having to use the voltage compensation tables and its not really an ideal situation having everything running at 2-3 volts less than it should.
I took my alternator apart again and ran through as many checks I could, following a very handy NZ auto electrical school tutor video about alternator testing online. I suspect the rectifier is kaput and I couldn't locate a cheap replacement.
I managed to locate a second hand alternator, pretty much the same unit and have bought it - now just waiting on the seller to sort their sh1t out.
In the meantime I got another similar alternator, this time a nippon denso unit from a Honda prelude that actually has a bit more clearance out back, but with an ugly grey painted steel cover. I ran some pigtail connections and bolted it up, started the engine and now have charging! Yay.
With things running at full voltage I tweaked the engines idle tune and cold start settings and am much happier with where I'm at there.
In case the other alternator turns out to not arrive/be a dud etc I decided to give this working unit I do have a bit of a polish and paint. In pics, finishing it off with wrinkle finish paint on the tin end cover.
Much better looking. I bolted it back in place and did one final run up to temp with a bit more tuning of the fuel table idle zone. I now have the engine able to idle at 650 and I could almost get a 50cent coin to balance on the plenum lid. The engine is still only sitting on the table, not bolted in place so I cant really expect it to be perfectly smooth. I think it idles a bit nicer at around 750- 800, a zone where its also running leaner at close to 14.7. Lots of time in the future to play with settings.
Confident its all a good starter and idler, plus realising I'm stalling on the next stage, I have now started to take the pump controller, cooling system and temporary wiring apart. The next time it will be started will hopefully be in the Imp. Next job is to reassemble the transmission, bolt the lot into the spare shell and sort out the gear shift linkage.
-
- Nurse, I think I need some assistance
- Posts: 18951
- Joined: Mon Mar 10, 2008 6:26 pm
- Location: West Midlands
Re: 1965 Hillman Imp soon with flat six from a Honda
Phew, such a lot to read, but knock-out results!
So many brackets and tweaks when doing these projects, but so interesting and good challenges.
Soon be all done and you will need another project!
So many brackets and tweaks when doing these projects, but so interesting and good challenges.
Soon be all done and you will need another project!
73T 911 Coupe, road/hillclimber 3.2L
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9