Meagsquirt EFI on a 2.2T - Real time data view with iPad

impmad2000 · Post by **impmad2000** » Mon Sep 18, 2006 9:15 am

Gary71 wrote:I do have the MAP connected to the original distributor take off, but currently the vacuum does not change when you blip the throttle, which suprised me.

The vacuum take off used in a conventional system is what is known as "ported vacuum", and is usually just up from the butterflies. You will need a "real " vacuum measurement (for the fuelling) but there is perhaps a "ported vacuum setting for the ignition only mode. Take off from the holes that you bunged up when you removed the over-run enrichment stuff should work a treat. if it is not stable, connect them all together, and use a mig tip in line (restriction) and an inline fuel filter (buffer) and this should even out any backpressures from the cam .
Cheers
Tim

Gary71 · Post by **Gary71** » Mon Sep 18, 2006 9:38 am

Cheers Tim,

The overrun enrichment ports sound like a plan, these enter about 4mm below the butterflies. I'll hook that up tonight.

1972_911t · Post by **1972_911t** » Mon Sep 18, 2006 2:41 pm

Did you get your MS ECU from the US or in the UK? Im wanting to do this for my 3.2 so I can ditch my AFM and eventually go to ITB's. I found a place that sells edis ready V3 ECU's for £260 inc vat is this about the going rate?

Thanks Steve

Gary71 · Post by **Gary71** » Mon Sep 18, 2006 3:04 pm

Hi Steve,

I bought my ECU from Bill Shurvington in the UK. We discussed a specification then he configured it accordingly and also put a base .msq file in to set up all the little details. ...and it worked first time

Great bloke, really knows his stuff, highly recommended. My MSI V3 ECU was £237 delivered including configuration for MS Extra (Spark control) using Ford EDIS, shift lights, tach output and PWM idle control. He can be found at : bill@shurvinton.fsworld.co.uk. He normally replies to emails past 10pm at night.

I can also recommend Chris at:

http://www.trigger-wheels.com

Another top bloke, good service and advice.

Good luck with your project, and I guess you have already immersed yourself in the reading on http://www.megasquirt.info Made my brain hurt.

Glenn75S · Post by **Glenn75S** » Mon Sep 18, 2006 3:32 pm

COIL C SHOULD BE CONNECTED TO THE CYLINDER THAT FIRES AFTER NUMBER 1.

Like number 6 you f'wit, not number 5.

Repeat after me: Firing order 1-6-2-4-3-5 So pair up 1&4 6&3 2&5

Gary,

I driven your car it has never had that firing order, as I remember its...

1-6- - -4-3-5, 1-6-2- - 3-5, - - 6-2-4-3-5

impmad2000 · Post by **impmad2000** » Mon Sep 18, 2006 3:35 pm

If there's enough interest, I can see about a DDK group buy.
I'm in the electronics industry, know people who'd be happy to solder them together (trained to full Mil spec soldering techniques) ... I know that the Imp club did similar, and you can really get the price down for this parts. Any thoughts ?
Tim

Gary71 · Post by **Gary71** » Mon Sep 18, 2006 4:02 pm

I driven your car it has never had that firing order

Cheeky bugger, at least it idles below 6000rpm....

Have you sorted it yet?

Glenn75S · Post by **Glenn75S** » Tue Sep 19, 2006 8:46 am

Gary71 wrote:
I driven your car it has never had that firing order
Cheeky bugger, at least it idles below 6000rpm.... Have you sorted it yet?

6000rpm is what it says in my misprinted Haynes manual!!!

List of jobs - MOT, Injectors, Front shocks, tune up, paint - Drive hard

Matt black70 · Post by **Matt black70** » Tue Sep 19, 2006 11:11 pm

Glen,you must have a great memory to remember the idle speed!,when did you last use it?.Matt

Ian Donkin · Post by **Ian Donkin** » Thu Sep 21, 2006 12:48 am

impmad2000 wrote:If there's enough interest, I can see about a DDK group buy.
I'm in the electronics industry, know people who'd be happy to solder them together (trained to full Mil spec soldering techniques) ... I know that the Imp club did similar, and you can really get the price down for this parts. Any thoughts ?
Tim

I'd be up for a group buy Tim - just need the ECU.

I'm sure Mick Cliff's watching with interest too

.

impmad2000 · Post by **impmad2000** » Thu Sep 21, 2006 7:19 am

Thanks Ian, I think there's a lot more watching this thread than would like to admit to

.....
Cheers
Tim

Gary71 · Post by **Gary71** » Thu Sep 21, 2006 7:41 am

there's a lot more watching this thread than would like to admit to

...best I get on with it then...

No progress this week. Currently suffering a prolonged parental visit so garage time has taken a hit. Full steam ahead soon though...

Mick Cliff · Post by **Mick Cliff** » Thu Sep 21, 2006 7:46 am

I'm sure Mick Cliff's watching with interest too

True!

But should I desecrate a 911/83 engine

Gary71 · Post by **Gary71** » Thu Sep 21, 2006 7:55 am

No Mick definitely not, what you say I get the 2.4T up and running on MS then I'll do you a swap for the old banger 2.7 unit

Glenn75S · Post by **Glenn75S** » Thu Sep 21, 2006 9:29 am

Matt black70 wrote:Glen,you must have a great memory to remember the idle speed!,when did you last use it?.Matt

Don't have to remember, I just look at where the dust is at its thinnest on the rev counter

DDK - Die Deutschen Klassiker

Meagsquirt EFI on a 2.2T - Real time data view with iPad

Re: Road to Meagsquirt EFI on a 2.4T - It runs on ECU igniti